![]() Never point or aim at someone's eyes or face. Always wear protective eye wear whilst using blasters. The items on this site are to be used by those 18years or older. The items on this site are safe as long as the operator uses it safely. BlasterTECH will not accept any liability for injury caused during or after modification. BlasterTECH will not accept any liability for damage or reduction of lifespan of your blaster. NOTE: Listing is for a Scarr Barrel and associated parts only, blasters and accessories are for display purposes only.īlasters are modified at your own risk. This product is designed / printed / stocked in house and can be dispatched ASAP. Crap happens sometimes, we understand, but they don't 'just break'. As with all our products, they are all comprehensively tested in the field and we have never broken our MkII scar. If you are concerned about it being knocked/broken, then please take care and or provide some protection for it. We drop test the MkII Scar from head height on to a hard tiled surface and they do not break. IE IT WILL BREAK IF YOU KNOCK IT IN TO SOMETHING (A BIT OF COMMON SENSE). IT PROTRUDES OUT THE FRONT OF BLASTER AND THEREFORE IS SUSCEPTIBLE TO KNOCKS. This not only dresses up the front end but provides some extra protection to the Scarr Barrel. Our 'Suppressor Muzzle' fits over the top of this scar barrel using the Nerf muzzle attachment point. DO NOT USE OTHER SIZE STRING as it will not perform as intended. This scar was designed to use this size string. Please look at the below video for the correct procedure stringing up your Scarr MkII.įor reference, this Scar uses 0.26mm string/line. Kit includes: Main Scar barrel, Scar adjusting tip, string. Please experiment to see what works for your blaster requirements. We recommend 1/8 to 1/4 turn on tip for appropriate pitched rifling. Scars do work with flywheelers, though its more efficient to use a canted cage with barrel tube guide we have found. Only to be used with Spring or Air blasters of 150fps and more, this gives you decent velocity to work with the scar effectively. ![]() Does not work with square headed darts where the dart head is the same diameter as the foam darts ie Accufakes. ![]() Elite darts are not recommended as they are too light in weight. Please check that your barrel has a Outer Diameter of 16mm or similar.Ĭompatible with Half-length or Full-length darts. The 16mm variant is a general/universal fitment designed to fit other barrel material in the market, meaning you may need to sand or use some tape for a snug fit on to your barrel. Whilst 17/32 and 9/16 variants are designed specifically to fit snugly. This Scarr barrel fits on K&S brand 17/32 and 9/16 brass tube, also 16mm outer diameter barrels. ![]() This enables you to fine tune the spin on the dart depending on requirements ie blaster power / dart velocity. It is adjustable, which means you can customise the rifling or 'pitch' on the strings via the front tip. Our Scar barrel has a focus on simplicity of stringing it up (Please see instruction video below). This takes the tension off the strings, so they don't stretch over time. Also, when you are done for the day, simply adjust the strings back to the neutral/straight position. The porting vents any excess air prior to the dart leaving the muzzle, this in turn eliminates the muzzle blast effect.įull Adjustability: Give you the power so you can adjust the rifling to suit your blasters power output and the darts you use. Ported/Vented: To eliminate 'muzzle blast' which can de-stabilise the dart when it exits the barrel. 6 strings provide more of a grip on the dart giving its spinning affect as it passes through the Scar. This give a more balanced centered affect on the dart providing a more consistent accurate shot. When a dart is fired and passed through the scar barrel, this imparts a spin on the dart witch in turn increases accuracy to the target.Ħ Strings: which has a 'hug' affect on the dart as it passes through, moreso than a 4 string design. The Scar barrel contains strings which are strung to create a 'rifling' (swirled) bore inside the barrel. Scar barrels are short length barrels that are attached to the end of barreled blasters. A solution to accuracy issues on higher velocity blasters are a well designed Scar barrel.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |